Networking interview questions/Answer set-2

Explain IP, TCP and UDP.

TCP – Transmission control Protocol is used to establish communication between nodes or networks and exchange data packets. It guarantees delivery of data packets in the order they were sent. Hence it is most commonly used in all applications that require guaranteed delivery of data. It can handle both timeouts (if packets were delayed) and retransmission (if packets were lost). The stream of data is transmitted in segments. The segment header is 32 bit. it is a connectionless communication protocol at the third level (network) of the OSI model.

IP – Internet protocol is used for transmission of data over the internet. IP uses IP addresses to identity each machine uniquely. Message is sent using small packets. The packet contains both the sender and receivers address. IP does not guarantee the delivery in the same order as sent. This is because the packets are sent via different routes. It is a connectionless communication protocol at the third level (network) of the OSI model.

UDP – User Data Protocol is a communication protocol. It is normally used as an alternative for TCP/IP. However there are a number of differences between them. UDP does not divide data into packets. Also, UDP does not send data packets in sequence. Hence, the application program must ensure the sequencing. UDP uses port numbers to distinguish user requests. It also has a checksum capability to verify the data.




What is multicasting?

Multicasting allows a single message to be sent to a group of recipients. Emailing, teleconferencing, are examples of multicasting. It uses the network infrastructure and standards to send messages.

Explain the functionality of PING.

Ping Is particularly used to check if the system is in network or not. It also gives packet lost information. In windows ping command is written as ping ip_address. The output returns the data packets information. The number of packets sent, received and lost is returned by PING.

What is a MAC address?

A Media Access Control address is a unique identifier that is assigned to the network adapters or NICs by the manufacturers for the purpose of identification and used in the Media Access Control protocol sub layer. It is a 12 digit hexadecimal number. A MAC address usually encodes the registered identification of the manufacturer, if the address is assigned by the manufacturer. It some times also called as Ethernet Hardware Address / physical address/ adapter address.

Explain Spanning-Tree protocols.

Spanning Trees are a standard technique implemented in LAN connections. On a mesh topology, a set of spanning tree algorithms were developed for prevention of redundant transmission of data along intermediate hops between a source and a destination host. In the absence of spanning trees, a mesh network is flooded and rendered unusable by messages by circulating within a loop that is infinite, between hosts. An algorithm used in transparent bridges which determines the best path from source to destination to avoid bridge loops.

At the time of STP initialization in a network, its first action is to utilize the Spanning Tree Algorithm for selection of a root bridge and a root port. The root bridge is the network which has lowest-value bridge identifier. All the switches on the network use Bridge Protocol Data Units to broadcast the bridge IDs to the other switches in that network. Soon after selection of the root bridge, determination of the root ports on all other bridges is done.

What is the use of IGMP protocol?

Internet Group Management Protocol: - It allows internet hosts to participate in multicasting. The IGMP messages are used to learn which hosts is part of which multicast groups. The mechanism also allows a host to inform its local router that it wants to receive messages.

What are Ping and Tracert?

Ping and tracert are the commands used to send information to some remote computers to receive some information. Information is sent and received by packets.

Ping I particularly used to check if the system is in network or not. It also gives packet lost information. In windows ping command is written as ping ip_address
Tracert is called as trace route. It is used to track or trace the path the packet takes from the computer where the command is given until the destination. In windows ping command is written as tracert ip_address

Explain RSVP. How does it work?

Resource Reservation protocol is used to reserve resources across a network. It is used for requesting a specific Quality of Service (QoS) from the network.

This is done by carrying the request (that needs a reservation of the resource) of the host throughout the network. It visits each node in the network. RSVP used two local modules for reservation of resources. Admission control module confirms if there are sufficient available resources while policy module checks for the permission of making a reservation. RSVP offers scalability. On a successful completion of both checks RSVP uses the packet classifier and packet scheduler for the desired Qos requested.

Explain the concept of DHCP.

Dynamic Host Configuration Protocol is used assigning IP addresses to computers in a network. The IP addresses are assigned dynamically. Certainly, using DHCP, the computer will have a different IP address every time it is connected to the network. In some cases the IP address may change even when the computer is in network. This means that DHCP leases out the IP address to the computer for sometime. Clear advantage of DHCP is that the software can be used to manage IP address rather than the administrator.


What are the differences between a domain and a workgroup?

In a domain, one or more computer can be a server to manage the network. On the other hand in a workgroup all computers are peers having no control on each other.

In a domain, user doesn’t need an account to logon on a specific computer if an account is available on the domain. In a work group user needs to have an account for every computer.

In a domain, Computers can be on different local networks. In a work group all computers needs to be a part of the same local network.


Explain how NAT works

Network Address Translation translates and IP address used in a network to another IP address known within another network. A NAT table is maintained for global to local and local to mapping of IP’s. NAT can be statically defined or dynamically translate from a pool of addresses. The NAT router is responsible for translating traffic coming and leaving the network. NAT prevents malicious activity initiated by outside hosts from reaching local hosts by being dependent on a machine on the local network to initiate any connection to hosts on the other side of the router.